Engine

EMPI 48/51 IDA/EPC manifolds are the standard for most IDA installations. This is a tall straight manifold that has a ball burnished finish and extra material at the base for port matching to the cylinder head. This manifold is for a stock style cylinder head stud pattern. All kits include Intake an..

EMPI 48/51 IDA/EPC short manifolds allow extra clearance for use with air cleaners or velocity stacks. All kits include Intake and Carburetor Base Gaskets, Studs, Nuts, Spring Washers and Extended Nuts.  Installation Note: These are straight manifolds and will offset the carburetors. May n..

The versatile EMPI intake manifold is compatible with a range of carburetors, including EMPI EPC 32/36F carbs, Weber DFV/DFEV carbs, and Holley 5200 Series carbs.Application Note: This is considered a universal part and can fit many different applications based on modifications to the vehicle. Appli..

This intake manifold is designed to fit 30 and 34 PICT carburetors and use single or dual port end castings. Intake manifold comes with pre-heat pipes. Application Note: This is considered a universal part and can fit many different applications based on modifications to the vehicle. Applicatio..

Intake Manifold T-1 66-70Shipping Note: This part ships at a dimensional weight NOT the actual weight...

Jaycee's Billet aluminum Jet Deflector for the 48 Weber IDA carburetor. Helps eliminate any disturbed air or turbulence above the jet stack. Fits over the stock jet screens. These jet deflectors will enhance your engines performance and dress up your motor.  Application Note: This is consi..

Lifter Hydraulic Mexico T-2 78-79 / Vngn 80-91, Sold as Set Lifters, Hydraulic, Stock, Mexico, Moresa, Sold as Set..

Made from a specially hardened iron alloy, then precision ground to exacting radius and finished to insure long life. Fits all Type 1 based 12-1600cc engines. Use with all new cams.  Installation Note: New camshafts should always be installed with new lifters.  Lifter to Camshaft..

Engle lifters are the perfect match for your camshaft choice. Lifters should always be replaced when installing a new camshaft, during the break in process lifters mate to the camshaft lobe. Insallation Note: Lifter to Camshaft clearances need to be checked for proper installation. A minimum of .040..

Engle lifters are the perfect match for your camshaft choice. Lifters should always be replaced when installing a new camshaft, during the break in process lifters mate to the camshaft lobe. Insallation Note: Lifter to Camshaft clearances need to be checked for proper installation. A minimum of .040..

One-piece design only weighs 72 grams with a 29mm wide head. Increase horsepower and eliminate valve-train float at high RPMs. Strongest hollow Type 1 lifter available with 60-degree radius face.Application Note: This is considered a universal part and can fit many different applications based on mo..

High performance and lightweight tool steel lifters for Type 1 camshafts. These Tool steel lifters weigh in at only 54 grams and have a head diameter of 28mm. Tool steel lifters don't require the same break in process as conventional lifters and can be reused from camshaft to camshaft without limita..

High quality stock replacement solid lifter made by Febi/Bilstien for late model 12-1600cc Volkswagen engines.Lifters, Solid, Stock, Febi/Bilstien, Sold as Set..

Cam Follower Riosulense 12-1600cc Brazil.  Lifters, 113109309CBR, Solid, Stock, Brazil, Riosulense, Sold as Set..

Cam Follower Moresa 12-1600cc Lifter, Solid, Stock, Mexico, Moresa, Sold as Set..

Cam Follower (Solid) T-2/4 17-2000cc, Sold as Set Lifters, 021109309G, Solid, Stock, Brazil, Riosulense, Sold as Set..

Cam Follower Each Moresa 12-1600cc Parkerized, Sold as Set..

Main Bearing dowel pins for bearing alignment to the engine case. Engine Case requires 5pcs. Main Bearing Dowel Pins, Sold as Set..

Silverline main bearings have a steel backed center main bearing for added support. Silverline is a Original Equipment Manufacturer/Supplier(OEM) out of Mexico. These bearings will fit 1700, 1800, & 2000cc VW Type 4 based engines in Bus and Vanagon. Please verify your Align Bore Diameter, ..

Silverline main bearings have a steel backed center main bearing for added support. Silverline is a Original Equipment Manufacturer/Supplier(OEM) out of Mexico. These bearings will fit 1700, 1800, & 2000cc VW Type 4 based engines in Bus and Vanagon. Please verify your Align Bore Diameter, ..

Silverline main bearings have a steel backed center main bearing for added support. Silverline is a Original Equipment Manufacturer/Supplier(OEM) out of Mexico. These bearings will fit 1700, 1800, & 2000cc VW Type 4 based engines in Bus and Vanagon. Please verify your Align Bore Diameter, ..